KABP Pressure-relief Electric Grease Lubricator-Electric PLC-controlled Series-Suzhou Weidoya Automation Electrical Equipment Co., Ltd.-Lubrication, Cooling & Intelligent Sensing

KABP Pressure-relief Electric Grease Lubricator

Metered lubrication

PLC-controlled.

Cartridge type

Inquiry

1. Operation and interval times are PLC-controlled.

2. Use with a CFB volumetric grease distributor for metered delivery.

3. Includes a pressure gauge for checking operating pressure.

4. A manual lubrication button provides forced lubrication.

5. An optional 60 kgf/cm² pressure switch detects damage to the lubrication lines.

6. An optional reed-switch oil-level detector can monitor level and send a signal automatically.

7. Fill the KAB reservoir through the grease nipple to prevent air and foreign matter from entering.

8. KABP-07 must be used with a 700 cc bellows-type grease cartridge. Replace the empty cartridge without time-consuming refilling. Cartridges are sold separately; refer to the bellows-type grease cartridge ordering codes.

9. Refer to the diaphragm pressure switch specifications for contact information.

◆ Dimensions

Model	Reservoir capacity.	Length L (mm)	Width W (mm)	Height H (mm)	Mounting hole pitch F (mm)	Weight (kg)
KABP-07	700 cc grease bag.	179	153	288	104	2.49

◆ Specifications

Motor Output Power	13W±12%
Voltage	DC24V
Current	1.4A
Maximum Discharge Rate	10cc/min
Maximum Discharge Pressure	100kgf/c㎡
Oil Outlet Size	Ø6, Ø8
Reed-type Oil Level Sensor	Optional (NC or NO contact)
Pressure Switch	Optional (NC or NO contact)
Applicable Oil Viscosity	NLGI 000-0

Reed-type oil level sensor contacts: NO sends a signal when oil is present; NC sends a signal when oil is absent.

◆ Wiring Diagram

M: Motor

GND: Ground

DK: forced lubrication button.

DS: pressure switch (optional).

WS: magnetic reed oil-level detector (optional).

Connect PLC: connection to PLC.

Power

Load

◆ Ordering Code

Model	Effective Capacity		Voltage		Oil Outlet Size		Special Request
KABP	07		K		3		※
	07	700 cc grease bag.	K	DC24V	1	Ø6	PC	Add a pressure switch.,NCContact
					3	Ø6 (with pressure gauge)	PO	Add a pressure switch.,NOContact
					4	Ø8	RC	Add a magnetic reed oil-level detector.,NCContact
					5	Ø8 (with pressure gauge)	RO	Add a magnetic reed oil-level detector.,NOContact

Note: Grease cartridges are sold separately.

◆ Bellows Grease Cartridge Specifications

Ordering Code	Specification	Grease Type	Lubricant Viscosity	Minimum Order Quantity
I01D0021	700 cc Bellows Grease Cartridge	Mobilux EP023	NLGI 000	--
I01D0012	700 cc Bellows Grease Cartridge	Mobilux EP0	NLGI 0	--
I01D0013	700 cc Bellows Grease Cartridge	Mobilux EP1	NLGI 1	100
I01D0029	500 cc Bellows Grease Cartridge	Idemitsu Polylex UMF	NLGI 000	6
I01D0030	700 cc Bellows Grease Cartridge	Idemitsu Eponex IM	NLGI 1	6

◆ Replacement Procedure

1		Hold the grease cartridge cover firmly and turn it counterclockwise to loosen it.
2		Remove the cover and spring.
3		Turn the empty grease cartridge counterclockwise and remove it.
4		Before installing a new cartridge, squeeze out a small amount of grease to prevent air entering the lubricator.
5		Turn the new cartridge clockwise to secure it to the cover base.

6		Refit the cover and spring.
7		Turn the cover clockwise to secure it to the base and complete cartridge replacement.